Alpine Electronics KTP-445U Amplifiers

Alpine Electronics KTP-445U Amplifiers 

Maybe your audio system suits you pretty well, but lacks the clean power you need to really enjoy your music. Maybe you also don鈥檛 want a big, current-hungry amp that robs precious cargo space and empties your bank account. If that describes you, there is a solution.

The 鈥淗ead Unit Power Pack鈥 by Alpine is an add-on 4-channel amplifier for use with virtually any aftermarket radio or OEM system. Best of all, it鈥檚 small enough to mount behind the dash near your radio! Rated at 45 watts per channel at either 2 or 4 ohms, the power pack gives your system a nice power boost, and it sells for only $149.95 in the U.S. or $179.95 in Canada.

Features

The KTP-445U is a basic rectangular amp measuring 7.5-inches long, 2.5-inches wide, and 1.5-inches high. The small size and slender shape allows it to be hidden almost anywhere, so you don鈥檛 lose cargo space, and it鈥檚 light enough that you can mount it on any flat surface using hook and loop fasteners. Both ends of the amp have connections for the included wiring harnesses and the 15-amp mini ATC fuse and gain controls. Pre-amp inputs are also included for typical balanced high-level and RCA connections. The low level inputs are handy for using the amplifier in applications that don鈥檛 have a traditional source unit (motorcycles and ATVs), where you would use an MP3 player as your source. There is also a switched 12-volt output wire to control additional amplifiers, and the amp is bridgeable for 2- and 3-channel configurations. Thoughtfully, the harnesses are long enough for a variety of mounting locations without needing to add wire.

The KTP-445U is equipped with built-in crossovers to select the front and rear channels. Available crossover frequencies are 60, 80, and 120 Hz. Rubber plugs at the bottom of the amplifier cover the frequency filters, 2- or 4-channel input selector switches, and either high level or RCA inputs. The amplifier is a Class D design for high efficiency operation, but it is designed to drive either 2 or 4 ohm loads - making it compatible with virtually any OEM or aftermarket speaker system.

Listening

The KTP-445U adds noticeable power to your system compared to a typical head unit, and sounds good doing it. The little amp adds virtually no additional character, and does exactly what a good amp should - faithful reproduction of the recording with adequate power. The amp has no audible noise floor, and draws very little current.

Alpine Electronics KTP-445U Amplifiers Alpine Electronics KTP-445U Amplifiers

Performance / Bench Measurments

On the test bench the KTP-445U performs like a typical Alpine amplifier. As I suspected, the frequency response is exceptionally flat, and the signal-to-noise ratio is excellent. The input sensitivity has plenty of adjustment range to handle virtually any input source, and even after hours of fairly high volumes, the amp is barely warm.

Conclusion

While many of us have been brainwashed with the 鈥渁mps are big and go in the trunk鈥 ideology, the Alpine KTP-445U makes us re-think this. Sure, you aren鈥檛 going to win any SPL contests with it, but the high efficiency design, ultra compact size, and startlingly good sound might make it the perfect amplifier for you.

Alpine Electronics KTP-445U Amplifiers

Technical Data

The following power measurements were obtained using industry standard methods. (1 kHZ @ 1.0% THD+N - Battery voltages shown +/- 0.2 V)

Manufacturers Rated Power    Actual Measured Power
@  1.0% THD+N                  @ 14.4 V Battery   
@  1.0% THD+N                  @ 12.6 V Battery 
  45 x 4 @ 4 Ohms      48 x 4 @ 4 Ohms     37 x 4 @ 4 Ohms

  45 x 4 @ 2 Ohms      45 x 4 @ 2 Ohms     38 x 4 @ 2 Ohms

Signal to Noise Ratio referenced to 2V output.
(CEA-2006A)  (1 watt @ 4 ohms)    -89.2 dBA
Signal to Noise Ratio referenced to full 4 ohm output.     -106.0 dBA
Distortion at rated power     0.6%
CEA-2006A rated 4 ohm Power (minimum power per channel developed over the entire audio bandwidth)     47 watts/ch
Maximum Efficiency at full 2 ohm power per ch.    82.8%
Idle Current (warm)    0.5 A
Maximum Current @ full power 2 ohms per ch.    16.2 A
Frequency Response (-3dB)    10 Hz 鈥 46 kHz
Stereo Separation (Crosstalk)    -76.7 dB @ 5 kHz

4 Ohm Power vs THD

Max Flat - Freq Response Crossover Range - Freq Response

Related Articles

2024 Nissan Z Nismo 鈥 Pros and Cons 2024 Nissan Z Nismo 鈥 Pros and Cons
The Nissan Z sports coupe was all-new for a seventh generation in 2023, and last year the top-line Nismo was introduced. We were lucky enough to get...
Walking the walk: Talking the Brap Brap Brap Walking the walk: Talking the Brap Brap Brap
As a car journalist, I spend my days writing about and reviewing other people鈥檚 builds 鈥 their visions, their stories. I analyze, critique, and...
February 2025 Event Calendar February 2025 Event Calendar
February 1, 2025 - Elite Tuner x GearHead SocietyLas Vegas   Silverton Hotel and Casino3333 Blue Diamond Rd Las Vegas, NV 89139https://tickets....
Rivian R3X Has Intriguing Performance Potential Rivian R3X Has Intriguing Performance Potential
Last March, Rivian revealed its new midsize platforms that would serve as the basis for the forthcoming R2 and R3 models that are expected to go on...
Cadillac Launches LYRIQ- V Cadillac Launches LYRIQ- V
If you weren鈥檛 sure Cadillac鈥檚 vaunted V-Series high-performance sub brand would survive the marque鈥檚 shift to electrification, we have good news: it...
AXDSP-X: The Ultimate Sound System Upgrade Solution AXDSP-X: The Ultimate Sound System Upgrade Solution
Specifically designed for BMW models(2010-2020), the AXDSP-X provides installers with a quick, cost-effective way to enhance vehicle sound systems. It...