Stinger Interconnects

Over the years I鈥檝e probably installed or worked on literally thousands of car audio systems. One of my specialties when I was a professional installer, was the prevention of noise shi6312_optor more often the removal of noise from someone else鈥檚 install. During most of those years I often pondered, sometimes quite verbally (and with great disdain), the choice of our industry to use RCA cables as signal conductors. From a pure physics point of view, it simply doesn鈥檛 make sense. You take a very low level, complex AC signal (your music) and run it over a very electrically noisy vehicle chassis. In a coaxial cable in many cases, which by nature will make noise problems worse! Add to that, the fact that the connectors typically don鈥檛 lock together, and then we install them in a vehicle, subject to all kinds of vibration and changes in temperature. Quite amazing when you think about it. An RCA type cable is actually about the worst possible choice we could have made, but, here we are.

It鈥檚 always fairly astonishing to me that we are able to get things as quiet as we do. Suffice to say, your choice if interconnect cable can make a big difference in whether or not you end up with intermittent signal, signal degradation, or the dreaded 鈥渁udible tachometer鈥 alternator noise or not.

I suppose it鈥檚 pretty obvious by now that a properly constructed cable is fairly important, and so are the cable ends. A good tight fit, and consistency in sizing are important to make sure all the signal gets to its intended destination, the inputs of your amplifiers! This is where a good quality cable can really make a difference, and it just so happens the experts at Stinger Electronics recently sent over a few samples their latest and greatest HPM Level 3 interconnects.

The first kit is called an Stinger SHI2317, and it鈥檚 a 17 foot long pair of interconnects. What makes this special are the great features that have been incorporated into the product. First, the cable ends themselves are sturdy and made of CNC machined aluminum. Electrical contact areas are coated with what Stinger calls Shoc-Krome, to provide good SHI231_optelectrical conductivity and resist corrosion. The outer shell of the RCA ends are tapered and split, and can be locked into place my tightening the blue anodized barrel, which has thoughtfully been given a tightly fitting rubber grip so you can get a good hold on it. The center pin of the connector is also split, which helps to optimize the contact, and provide a good solid connection. The cable is double shielded, and of the twisted pair variety, which has been proven to reduce radiated noise transmission, providing the twists are tight enough. The cables are also directional, which refers to the fact that the 鈥渟ource鈥 end of the cable has the RCA shell connected to the cable shielding, and it 鈥渇loats鈥 on the other end. This technique can be helpful in reducing noise caused by ground loops, or poor impedance matching of components. The pair of cables merge into a single larger diameter jacket, which is covered in a braided open mesh material. This mesh material not only provides some protection to the cable, but it also is easier to install, because it prevents the jacket material from getting hung up on things during the installation. The cables have a very nice fit and finish, and Stinger assures us that the entire cable has no internal solder connections, and is pure oxygen free copper.

The second kit ( Stinger SHI6312) is very similar, except there are 3 pairs (6 individual cables) all included in a single cable run. The CNC machined ends are silver this time, and slightly different in appearance, but still have all the same features as the aforementioned cable. Cable identification is made possible via small colored O-rings that are found just behind each RCA shell. The cable itself follows the double shielded, directional, twisted pair design as before, and also includes the protective and helpful mesh covering.

These Stinger HPM Level 3 kits are truly high quality cables that will do justice to even the most demanding applications. The stereo pair in the 17 foot length sells for under 50 bucks, and the full 6 conductor cable in a 12 foot length can be purchased for about $80.00. Pick some up, and you鈥檒l know you鈥檝e done your best in ensuring the integrity of your signal transfer.

USA:
CANADA:

Related Articles

Stinger Electronics - enLIGHT10 RGB Lighting Solutions Stinger Electronics - enLIGHT10 RGB Lighting Solutions
Stinger Electronics, an industry leader in aftermarket vehicle technology, introduces enLIGHT10 RGB lighting solutions. The enLIGHT10 series offers a...
Papadakis Racing Toyotas Return To Irwindale For Formula DRIFT Finale Papadakis Racing Toyotas Return To Irwindale For Formula DRIFT Finale
Fredric Aasbo and the Rockstar Energy Toyota GR Supra lead championship points IRWINDALE, California (October 21, 2021) 鈥 The Papadakis Racing Toyota...
2020 Kia Stinger GT-C: A Convertible Concept 2020 Kia Stinger GT-C: A Convertible Concept
Our friend, Aaron Vaccar, recently posted on his social media pages of a build he鈥檚 been working on and it caught my attention. The Stinger GT-C...
Sound Deadening: Getting The Most Out Of Your Speaker Install Sound Deadening: Getting The Most Out Of Your Speaker Install
Two materials that will change your tune. You wouldn鈥檛 turbo an engine without also upgrading the fuel injectors, the exhaust, and intake, would you...
香蕉视频直播 Builder Showcase: AJ Velasco's 2020 Tesla Model 3 Performance Edition 香蕉视频直播 Builder Showcase: AJ Velasco's 2020 Tesla Model 3 Performance Edition
During our virtual walk-through of KnowledgeFest.LIVE, we noticed AJ Velasco's 2020 Tesla Model 3 Performance Edition as a featured vehicle for Orca...
Super Star(ion): Harrison Roske 1986 Mitsubishi Starion Super Star(ion): Harrison Roske 1986 Mitsubishi Starion
The lack of aftermarket support for a platform can be a total bummer, especially when you want to thrash it, but those tough situations can also give...